This timer is equipped with a rechargeable Ni-Mh battery which will protect your programs during power failure for up to 30 days. For example if the current time is 2:00PM and you just programmed the unit to turn ON at 1:00PM, you will need to press the manual override key to turn it ON.Thereafter, the unit will resume normal operation (automatic).

When you initially program the unit it may be necessary to press the manual override key as the unit will not look back to determine if it should be ON. Pressing the door will override the timer setting and will manually turn the switch ON and OFF. Then press the “PROG” key in order to delete this particular program.ġ20VAC 60Hz 15A Resistive 15ATungsten 1HP Then press the “HOUR” and “MIN” keys until -:- is displayed. To delete a particular program simply press the “PROG” key until the desired program is displayed.Ģ. When complete press the “CLOCK” key to return to current time and day.ġ. Any program can be edited by pressing the “HOUR”,“MIN”, and “DAY” keys.Then press the “PROG” key in order to accept the changes.ģ. Each time you do this you will be able to scroll thru the programs.Ģ. To review the programs that have been entered, press and release the “PROG” key. Follow the steps above to complete programming.ġ. When programming ON/OFF events, all days are indicated by default.To change the day selection simply keep pressing the Day key and the display will change as follows:Ħ. Note that a total of 7-ON and 7-OFF events can be programmed.ġ. If complete press the “CLOCK” key to return to current time and day.ĥ. When complete press the “PROG” key once.Ĥ. See block programming below for selecting different days. Using the “HOUR” and “MIN” keys enter the desired OFF time. When complete press the “PROG” key once.ģ. Using the “HOUR” and “MIN” keys enter the desired ON time. Press the “PROG” key once.TIMER 1 on - : - appears.Ģ. Now the timer is in operation and ready to be programmed.The colon “:” after the hours will continuously flash indicating that the clock is running.ġ. Release the “CLOCK” key once the time and day have been entered. If any keys are pressed for a prolonged period, the display will advance rapidly.Ħ. Press the “DAY” key to advance the day.ĥ. Press the “MIN” key to advance the minutes.Ĥ. Find all the frequently asked questions and user manual for CLIPSO + PRECISION. Press the “HOUR” key to advance the hours.ģ. Press and HOLD the “CLOCK” key during this entire procedure.Ģ. The display should flash 12:00AM on Monday.ġ. Press the “RESET” button using a paper clip.Ĥ.

Lift up the bottom of the door using a small slotted screwdriver.ģ. Mount the timer to the wall box being careful not to crush any wires.ġ. Tuck the wires into the wall box leaving room for theTimer. Note: Be sure that all wire nuts are secure.Ĥ. Often neutral wires can be found in the back of the wiring box wrapped in a wire nut.Ĭ) Connect the Hot/Live wire of Load to the Red wire fromTimer.ĭ) Connect the Ground wire to the Green wire fromTimer. Connect the wires ofTimer and wall box as followed by using the wire nuts provided.Ī) Connect the Hot/Live wire of main power to the Black wire fromTimer.ī) Connect the Neutral wires in outlet box to the White wire fromTimer. ? If no numbers are visible on-screen, plug the timer into an outlet and let the timer.3. my on/my off settings, to-the-minute countdown, manual override and more. MyTouchSmart Outdoor 6-Outlet Light Sensing Yard Stake Timer with 6ft. It was 4pm, my schedule was set for 330 pm. Myts timer manual Rotate the dial so that the pointer’ s direction corresponds to the powered by Peatix : More than a ticket.I did the setup, time is correct with am/pm, on/off times are set up.

Note: When a “my on” or “my off” time is set, the active program accordance with the instructions may cause harmful interference to radio communications Once you reach the desired “my on time,” either wait 5 seconds, press “my on time” again or Bookmark this page and add it to your phone home page. Enter a USER name (6 characters, NO spaces). You can also check for the same email on your home computer. Press “my on time,” then use up and down arrows to set on time. Depending on the phone service this may take 1-2 minutes. My touch smart timermytouchsmart timer 26898 troubleshooting

Owners manual my smart touch timer